Install a Furman M-10x E Power Conditioner in to the top slot of your rack, and the ten switched outlets in the rear panel will power up and protect all your equipment up to a 10-amp load.

The Furman M-10x E Power Conditioner is the perfect low-cost AC power solution for any rack mount system.


– Instrument Rigs: You’ve got a rack for your effects, preamps, tuner…You’re going to plug that into the wall? One big spike and your rig is up in smoke. Furman’s standard level surge/spike protection defends your gear from the spikes and surges that are so common at gigs and practice spots. With Furman’s standard level RFI/EMI filtration, you’ll get a quieter tone without pops, crackles, and the local radio station coming out of your amp. Plus, dual pull-out lamps (M-10Lx E) let you see your rack without turning the house lights on.

– Recording: Can’t track down where that noise is coming from? Your mix sounding flat? With Furman’s standard level RFI/EMI filtration you’ll lower the noise floor caused by the dirty AC power coming into your console or DAW. Furman’s standard level surge and spike protection keeps your sensitive digital equipment from acting funny or burning up due to everyday spikes and surges. With a 10A capacity and eleven total outlets, it’s enough to power your whole home studio.

– DJ Equipment: Bars, clubs and other event venues have some of the worst power out there – from air compressors turning on and off to light shows pulling current loads up and down, the AC power can be a strain on the circuits in your rig. Furman’s standard level protection and filtration keeps the bad stuff out.

– Pro Audio: When you’re out there gigging, you never know what kind of power you’re going to get. The wear and tear on mobile rigs eventually takes it toll – that’s why it’s smart to plug into Furman’s standard level protection and RFI/EMI filtration. It keeps your equipment safe and sounding clean. Whether you’re setting up a show at the local club or powering up the church band for their next service, make sure you give them power they can trust.

Furman M-10x E Power Conditioner Specifications:
– Maximum Output Current: 10 amps
– Line Cord: 1.5 meter, removable, IEC C-13 female to Schuko male
– Operating Voltage: 230VAC 50Hz
– Spike Protection Mode: Line to neutral
– Energy Dissipation: 305 joules
– Peak Impulse Current: 12,000 amps
– Maximum Continuous Opterating Voltage: 650 Volts
– Noise Attenuation: Transverse mode: Greater than 20dB, 1.5Mhz to 200 Mhz
– Dimensions: 1.75” H x 19” W x 7.5” D
– Weight: 2.3 kg.
– Safety Agency Listing: CE
– Warranty: Merit Series units are protected by a limited three year warranty covering defects in materials and workmanship.

Descrizione in Italiano:
Il Furman M-10x E Power Conditioner è un Distributore e Filtro di rete 230V con 11 prese IEC di cui una frontale e 10 posteriori in formato 1unità rack.

Specifiche tecniche
– Interruttore generale frontale
– Led di segnalazione protezione apparecchi inserita
– Presa maschio entrata alim.posteriore
– Breacker 10A posteriore
– Potente filtro anti RF ed interferenze elettromagnetiche ( RFI/EMI )
– Sistema di protezione dai picchi di tensione ( 650Volts ) / corrente ( 12.000Amp.)
– Max.potenza in transito 10A a 230VAC
– Dimensioni: 44x483x190mm
– Peso 2,3Kg
– Colore nero

Furman M-10x E Power Conditioner Furman M-10x E


Approfitta della spedizione gratuita!

Immediatamente Disponibile in Magazzino, Pronta Consegna!